MONKHUM.CC
• Soundscape Studio Suite
⛶ F11
Soundscape Machine Workstation • FW v2.5

MON2 WAV Convertor

Official Web Audio Converter & Serial Flasher for (o) MON 2 : SOUNDSCAPE MACHINE
Conversion Settings & Audio Format
16-bit PCM (High Quality & Zero-Latency)
Max Audio Duration: ~ 75.8s (1m 15s) Studio Master (48 kHz)
Studio Master Quality: Highest dynamic range, full-frequency audio fidelity. Perfect for drums, sound effects, and high-fidelity instruments.
Generated Output Filename Format:
mon2-16-48000-xxxx-07082026-0sec.bin
Max capacity ~ 75.8s (1m 16s) (16-bit, 48.0kHz on 6.9MB Flash)
Loaded: 0.0s • Remaining: 75.8s
0.0% Used (0 Bytes / 6.94 MB)
Master Combined Waveform
0 / 12 Files Loaded — Drag & Drop up to 12 WAV files or
Total: 0.00s | Max: 75.8s
▶ Start: 0.00s
End: 0.00s ◀
0.00s
Flash Existing .bin File

Already have a previously generated sound pack? Upload it directly here for flashing.

No file selected
Direct Serial Flash to MON2 (Audio Bank Flashing Guide)

Flash .bin sound pack directly to MON2 via USB-C (requires Google Chrome or Microsoft Edge).

🔌 Which COM Port should you select when prompted?
✅ Select: USB Single Serial (COMx) or USB-Enhanced-SERIAL CH9102 / CP210x
This is the dedicated Hardware UART Flasher chip used to flash .bin audio packs and firmware in Bootloader mode.
❌ Do not select: MON-2 SOUNDSCAPE MACHINE - MON2 Web Serial CDC (COMx)
This is the runtime CDC port for MIDI / CC / Chord communication (will fail to flash if selected outside B2 bootloader).
📌 Step-by-step Flashing Instructions (1 – 6):
  1. Prepare Audio Files: Drag WAV audio files into the tracks above (the system automatically compiles them into memory when you click Flash to MON2 — or click Choose .bin File if you already have a compiled pack).
  2. Connect USB-C Cable: Connect the USB-C cable from your computer to the MON2 USB port (close any other apps using serial ports).
  3. Enter Bootloader Mode:
    • Turn Power switch OFF.
    • Press and hold button B2 on MON2, flip Power ON, then release button B2.
  4. Click Connect MON2 below: When the browser popup appears, select USB Single Serial (COM...) and click Connect.
  5. Click Flash to MON2: When status displays "Connected! Ready to flash", click Flash to MON2 and wait for 100% progress.
  6. Power Cycle to Use: When status says "Flash complete!", flip Power OFF then ON once. Your new sound kit is ready in Sampler Mode!

Comprehensive Usage & Flashing Guide (Step-by-Step)

Step 1: Prepare and Convert Audio Files to .bin

1. Select desired Target Sampling Rate (e.g. 48 kHz for maximum quality, or 22.05 kHz for longer audio capacity).
2. Drag up to 12 audio files into the Master Combined Waveform (or click + Browse).
3. Adjust Start / End / Gain / Normalize points or drag playhead to preview individual tracks (total capacity must not exceed 6.94 MB).
4. Click 1. Compile & Generate mon2wav.bin to build your sound pack (you can Download for backup or click Flash .bin directly).

Step 2: Select Port & Flash to MON2 Hardware

1. Connect USB-C cable and enter Bootloader mode: Power OFF → Hold button B2 → Power ON → Release B2.
2. Click Connect MON2 and in the browser device picker:
  • ✅ Select USB Single Serial (COMx) (CH9102 UART flasher port).
  • ❌ Do not select MON-2 SOUNDSCAPE MACHINE - MON2 Web Serial CDC (runtime CDC MIDI port).
3. Once connected, click Flash to MON2, wait until 100%, then power cycle MON2 to start jamming with your new samples!